Difference: Jun2016CERNTBLog (10 vs. 11)

Revision 112016-06-11 - AtlasjSilicon

META TOPICPARENT	name="June2016CERN"

back to June Testbeam page

June 2016 CERN Testbeam Logbook

June 2016 CERN Testbeam Logbook
- Add Log
- More Information

Add Log

May 25 9:00 Starting Testbeam preparation at H6A beam area. Setup HSIO2 and updated Firmare.

-- Koji Nakamura - 2016-05-25

June 6 non-irrad sensor tuning start & done, Auto trigger data taking (3dut & 5tel) in beam line -> OK

-- Atlasj Silicon - 2016-06-06

June 6 22:47 check long auto trigger run (about 3h, 3dut & 5tel) -> telescopes & DUT are stable (don't stop run) by K.Sato

-- Atlasj Silicon - 2016-06-06

June 7 10:30 Updated firmware on Artex-7 of IFAE(AFP)'s HSIO2 (HsioCosmic _V11N_CosmicNew.bit) by H. Sawai

-- Atlasj Silicon - 2016-06-07

June 7 11:00 Started tuning for irrad-module by H. Sawai

-- Atlasj Silicon - 2016-06-07

June 7 19:36 Succeeded in remote controlling from the hut. Started 3SCC auto-trigger run with GeoID:31. by H. Sawai

-- Atlasj Silicon - 2016-06-07

June 7 23:47 Started run for 3SCC (no beam yet). GeoID:31, Run Number:1930~ by H. Sawai

-- Atlasj Silicon - 2016-06-07

June 7 23:52 All sensor tuning done by K.Sato

-- Atlasj Silicon - 2016-06-07

June 8 23:34 Adjusted position of 3 SCCs, and started run (Run Number:1950~) by H. Sawai

-- Atlasj Silicon - 2016-06-08

Deleted:

<
<

June 9 10:04 KEK105,106,108 connectivity check at control room, but tuning is not good...(connecivity is OK) so need to tune in beam line before test by K.Sato

-- Atlasj Silicon - 2016-06-09

Added:

>
>

June 10 4:00 check sensor condition, KEK105RJ3 is out, other sensor install run control. but beam is stopping now...

Deleted:

<
<

June 10 4:00 check sensor condition, KEK105RJ3 is out, other sensor install run control. but beam is stopping now...

Atlasj Silicon - 2016-06-10

Deleted:

<
<

June 10 6:00 beam on & start alignment

-- Atlasj Silicon - 2016-06-10

Added:

>
>

June 11 8:30 5telescope run start (runnumber=2118). Please check run spreadsheet

-- Atlasj Silicon - 2016-06-11

June 10 morning~June 11 night summary

- 4chip run(KEK105,106,108) alignment OK & start

- HSIO2 inlink, outlink config file is incorrect -> change correct config file -> can take beam data

- include noise scan mask - make 4chip run reconstruction program, so please check　run quality sometimes

- telescope4 remove June 11 night, because of non event build. -> change 5telescope June 11 8:30

-- Atlasj Silicon - 2016-06-11

<--/commentPlugin-->

More Information

-- Koji Nakamura - 2016-06-05

View topic | History: r21 < r20 < r19 < r18 | More topic actions...