Tags:
create new tag
view all tags
---+ Magnetic Field Test Log Book ---++ Preparation ---+++ 5th October at Fuji 作業初日 原先生からMPPC+Scintillator×4(NR0~3) NR0、NR1は調子よく動作している。NR2、NR3の動作が不調。 →(NR0 || NR2) && (NR1 || NR3)でtrigger signalを発行するようにする。 ---+++ 6th October at Fuji TriggerのThresholdの調整。 調整後 (NR0 && NR1 && NR3)はCosmic muonが通ったようなsignalが発行されているが、NR3のThresholdが下がらないため、efficiencyが良くない 測定時のLogicとして(NR0 || NR2)&&(NR1 && NR3)&&(~all module busy signal OR)を考え中(busy状態があると、trigger numberのずれが生じるかもしれないため) Multi I/O boardのTX1からbusyが出力(trigger signalが入ってくると、Hitの有無に関係なくbusy signalが発行される) ---+++ 7th October at Fuji 4つのPixel moduleからのbusy signalを受け取るための回路基板作成 (僕はこの日いなかったので補足お願いします by kazuyukis) ---+++ 8th October at Fuji FPGAからのTrigger出力をMulti I/O boardに入れたときにbusy siganlが発行されないeventがあった。 →Trigger signalにある程度の幅がないとTriggerとして受け取ってくれないらしい。 Gate Generatorを使って、FPGAからの信号幅を広げてみたところ、Trigger signalがあるときにbusyが発行されるようになった。 →Gate Generatorを使わずにFPGA or 回路で信号幅を広げられるか考え中 ---+++ 9th October at Fuji real 4chip module(Ni/In)×4到着 tuning & source scan(10/10~12でThermal Cycleを行っておく) Spartan3 : NIMout3 is broken. 信号幅の大きさを大きくするためにTrigger unitの回路変更 UA733 → 4-11を繋げることにした(信号増幅) →NR0,1,3のtrigger signalはうまく出てくるようになった。 NR2は右側の可変抵抗が壊れている?かもしれないので修理が必要 ---+++ 13th October at Fuji 4chip module Thermal Cycle後のtuning & source scan KEK102,103,104に関してはtuning & ss 終了、バンプオープンは見られなかった。 KEK101に関してはthresholdを調整する(Vthin)部分が壊れているかもしれない(Thermal Cycle前から) trigger systemのNR2修理完了、4つとも動作している→(upper 2system or) & (lower 2system or)で間に2module入れてデータ取得中 Vertex7のclock取り出しについて考え中 ---+++ 14th October at Fuji KEK101 Thermal Cycle後のtuning & source scan KEK101はbump openが見られた & thresholdに関するregisterが壊れていそうVthinを変えてもthresholdが変わらない trigger*2 module*2 trigger*2で測定中→要解析 Vertex7でのclock取り出し難航中 ---+++ 15th October at Magnet am : setting(ステッピングモータの動作確認、位置調整) pm : magnet使用開始(ガウスメータでの測定、磁場耐性試験)→ https://docs.google.com/spreadsheets/d/1NmVqjLHLgbN6IvzleaJSCAGjhs-MDUzRaK3FYoLhjg4/edit?usp=sharing ---+++ 16th October at Magnet データ取得用のセットアップ→SCC(KEK80)を使って、MPPC triggerの動作確認→順調に動いてそう(富士B2でのセットアップ復元) 磁場耐性試験については順調に動作中(月曜日の朝までこのままの予定) latency checkを行った、defaultではlatencyが大きすぎたため。(Spartanでの処理の時間のためだと思われる) default latency in the source scan was 210 (clock) and LV1 value for the cosmic hit was around 5. (FE sorce scan it was 0-1) ---+++ 19th October at Magnet 9:00 Swiched off the Magnet (3hrs) 9:20 removed Pixel modules from Magnet area. 9:40 started source scan for KEK102-104 Source Scan 結果 → KEK101はtuningし直した。KEK102~KEK104はafterTCのtuningのままsource scan。 → 5V程の電圧をかけてconnectivity testを実行 → KEK102~KEK104はsource scanの結果より、bump openなし。 → KEK101:RJ4もbump open、RJ3 bump open悪化、RJ2 no response。<br />  RJ4のno responseを解決しようとして15度に保たれた恒温槽に入れてsource scanをしたところ、RJ4のopenが悪化した。<br />  RJ4はno responseのまま。 ---+++ 19th~23th October at Magnet 磁場を上げながらデータ取得(0T,0.5T,1.0T1.6T)→表参照 23th 16:00~ 片付け -- %USERSIG{KojiNakamura - 2015-10-10}% ---++ Comments <br />%COMMENT%
E
dit
|
A
ttach
|
Watch
|
P
rint version
|
H
istory
: r12
<
r11
<
r10
<
r9
<
r8
|
B
acklinks
|
V
iew topic
|
Ra
w
edit
|
M
ore topic actions
Topic revision: r12 - 2015-10-23
-
KazuyukiSato
Home
Site map
Main web
Sandbox web
TWiki web
Main Web
Users
Groups
Index
Search
Changes
Notifications
RSS Feed
Statistics
Preferences
P
View
Raw View
Print version
Find backlinks
History
More topic actions
Edit
Raw edit
Attach file or image
Edit topic preference settings
Set new parent
More topic actions
Account
Log In
E
dit
A
ttach
Copyright © 2008-2025 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki?
Send feedback