2021年1月

Article text.

-- Tatsuki Ueda - 2021-02-01

1/5

Pad-C2 Sensor measurement

- KEKampBoard version7 の信号の波形を見るための測定 (2回目)

- 20degC

- MPPC (external trigger)

Set up

(pad No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)

Measurement

10:46 180V, 0.0030uA, Trg rate 150Hz,

12:00 run stopped

runfile : pad_scinti_C2_kekv7_180V

12:01 185V, 0.0935uA, Trg rate 150Hz,

12:40 run stopped

runfile : pad_scinti_C2_kekv7_185V

Pad-C1 sensor measurement

- breakdown voltではC1とC2センサーでは同じgainが出ているのかを確認する為の測定

- 20degC

- MPPC (external trigger)

Set up

(pad No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,16) (4,3,15) ?

(1,2,1) (2,3,2) (3,1,15) (4,0,16)

翌日の写真がこの並び、なのでこっちが正しい?

Measurement - C1 sensor

19:10 274V, 0.0018uA, Trg rate 150Hz,

19:30 run stopped

runfile : pad_scinti_C1_274V

19:32 279V, 0.0029uA, Trg rate 180Hz,

19:52 run stopped

runfile : pad_scinti_C1_279V

19:54 284V, 0.117uA, Trg rate 150Hz,

20:14 run stopped

runfile : pad_scinti_C1_284V

19:54 289V, 0.353uA, Trg rate 150Hz,

20:14 run stopped

runfile : pad_scinti_C1_289V

/home/kitasyk/work/LGAD/LGADSoftware/runfile/ にあるけどgitにはあげてないです

1/6

Pad-C2 sensor measurement

- breakdown voltではC1とC2センサーでは同じgainが出ているのかを確認する為の測定(昨日の続き)

- 20degC

- MPPC (external trigger)

Set up

(pad No, ADC ch, Amp ch)


=> (1,2,1) (2,3,2) (3,1,15) (4,0,16) ?->要確認

Measurement - C2sensor

9:32 176V, 0.0012uA, Trg rate 180Hz,

9:52 run stopped

9:52 181V, 0.0030uA, Trg rate 180Hz,

10:12 run stopped

10:12 186V, 0.070uA, Trg rate 180Hz,

10:32 run stopped

10:32 191V, 0.79uA, Trg rate 180Hz,

10:52 run stopped

Pad-C2 Sensor measurement mounted on KEK16ch Board ver7

- KEKampBoard version7 の信号の波形を見るための測定 ->保護容量を外して再測定

- 20degC

- MPPC (external trigger)

Set up

(pad No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)

Measurement

15:27 180V, 0.0030uA, Trg rate 150Hz

16:22 run stopped

runfile : pad_scinti_C2_kekv7_180V_add

Trigger ->100ps遅らせて再測定

18:32 180V, 0.0025uA, Trg rate 160Hz

runfile: pad_scinti_C2_kekv7_180V_add2

1/7

Pad-C2 Sensor measurement

- KEKampBoard version7 の信号の波形を見るための測定 (4回目)

- 20degC

- MPPC (external trigger)

Set up

(pad No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)

Measurement

金属板でシールド+高さアップ

10:00 180V, 0.0038uA, Trg rate 150Hz,

10:30 run stopped

runfile :pad_scinti_C2_kekv7_180V_add3

高さ調整のみ

17:07 180V 0.0028uA

runfile : pad_scinti_C2_kekv7_180V_add4

Pad-C2 Sensor measurement

- クロストークABC比較のための測定

- 20degC

- MPPC (external trigger)

Set up

(pad No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)

Measurement

18:36 181V, 0.0029uA, Trg rate 150Hz,

19:36 run stopped

runfile :pad_scinti_C2_181V

1/8

Pad-C2 Sensor measurement &time difference by pad stack sensors

- KEKampBoard version7 の信号の波形を見るための測定 (5回目)

- 20degC

- MPPC (external trigger) reverse style

Set up

(pad No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)(5,0,3)(6,1,4)(7,2,13)(8,3,14)

Measurement

金属板でシールド+高さアップ

11:35 180V, 0.0079uA, Trg rate 150Hz,

12:02 run stopped

runfile :pad_stack_scinti_C2_kekv7_180V

Pad-B2 Sensor measurement

- クロストークのタイプ別比較、外部トリガーで行うため

- 20degC

- MPPC (external trigger)

Set up

(pad No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)

Measurement

15:37 229V, 0.016uA, Trg rate 150Hz,

17:00 run stopped

runfile : pad_scinti_B2_229V ---> /home/kitasyk/work/LGAD/monooki/に入ってます

Pad-A2 Sensor measurement

- クロストークのタイプ別比較、外部トリガーで行うため

- 20degC

- MPPC (external trigger)

Set up

(pad No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)

Measurement

18:08 326V, uA, Trg rate 150Hz,

run stopped

runfile : pad_scinti_A2_326V

1/12

Pad-C2 Sensor measurement &time difference by pad stack sensors

- KEKampBoard version7 の信号の波形を見るための測定 (6回目)

- 20degC

- MPPC (external trigger) reverse style

Set up

(pad No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)(5,0,3)(6,1,4)(7,2,13)(8,3,14)

Measurement

銅製の金属板でシールド+高さアップ

10:41-12:10 180V,0.0094uA , Trg rate 180V

銅製の金属板でシールド(大きさUP) +ねじ留めを外した

16:04-17:04 180V,0.0085uA , Trg rate 180V

1/13

Pad-C2 time resolution measurement

- 恒温槽下での時間分解能のデータが足りないので再測定

- 20degC

- MPPC (external trigger)

Set up

(pad No, ADC ch, Amp ch)

    下流側                 上流側
=> (1,0,3) (2,1,4) (3,2,13) (4,3,14) (5,4,5) (6,5,6) (7,6,11) (8,7,12)

Measurement

14:50-17:12 183V, 0.0245uA , Trg rate 150V

1/14

Pad-C2 Sensor measurement &time difference by pad stack sensors

- KEKampBoard version7 の信号の波形を見るための測定 (7回目)

銅製金属板有り

銅製のセンサーパッドが必要がないことを示すため、HVラインを切って疑似的に穴あきボードに似せたセットアップで再測定を行った。

- 20degC

- MPPC (external trigger) reverse style

Set up

(pad No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)(5,0,3)(6,1,4)(7,2,13)(8,3,14)

Measurement

17:38- 19:30 180V,0.0098uA , Trg rate 150Hz

StripUPC2 measurement

前取ったデータがよく分からなかったのでもう一回。

- 20degC

- MPPC (external trigger)

- FNALamp NO.1

Set up

(sensor No, ADC ch, Amp ch)


=> (1,0,9) (2,1,10) (3,2,11) (4,3,12) (5,4,13) (6,5,14) (7,6,15) (8,7,16) (1,8,8) (2,9,7) (3,10,6) (4,11,5) (5,12,4) (6,13,3) (7,14,2) (8,15,1)

Measurement

20:29 - 1:00 183V, uA , Trg rate 75Hz

1/15

StripUP Β2 measurement

クロストークの比較のための測定。

- 20degC

- MPPC (external trigger)

- FNALamp NO.2

Set up

(sensor No, ADC ch, Amp ch)


=> (1,0,9) (2,1,10) (3,2,11) (4,3,12) (5,4,13) (6,5,14) (7,6,15) (8,7,16) (1,8,8) (2,9,7) (3,10,6) (4,11,5) (5,12,4) (6,13,3) (7,14,2) (8,15,1)

Measurement

11:27 - 16:36 215V, uA , Trg rate 100Hz

1e14 C-1 PAD measurement

C-1 /PAD/1e14 /fnal

- 20degC

- MPPC (external trigger)

- FNALamp NO.9

Set up

(sensor No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)

Measurement

19:37 - 20:20 380V, 3.7uA , Trg rate 100Hz

KEK v7 stack C-2 PAD measurement

C-1 /PAD/1e14 /KEKv7

- 20degC

- MPPC (external trigger)

- KEK

Set up

(sensor No, ADC ch, Amp ch)

Measurement

20:40 - 25:10 180V , 0.89uA ,Trg rate 150Hz

1/18

1e14 C-1 PAD measurement

C-1 /PAD/1e14 /fnal

- 20degC

- MPPC (external trigger)

- FNALamp NO.8

Set up

(sensor No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)

Measurement

15:50 370V, 2.7uA , Trg rate 150Hz

16:50 360V ,1.99uA, Trg rate 150Hz

17:50 360V

C2 PAD stack

C2 / PAD / stack / fnal /timereso

- 20degC

- MPPC (external trigger)

- FNALamp

Set up

(pad No, ADC ch, Amp ch)

    下流側                 上流側
=> (1,0,3) (2,1,4) (3,2,13) (4,3,14) (5,4,5) (6,5,6) (7,6,11) (8,7,12)

Measurement

19:55 185V, 0.03uA , Trg rate 150Hz

23:30 run stopped

1/19

C-2 PAD Poly-si elec measurement

C2 / PAD / poly-si elec/ fnal

- 20degC

- MPPC (external trigger)

- FNALamp NO.3

Set up

(sensor No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)

Measurement

10:30 158V, 0.013uA , Trg rate 150Hz

12:00 run stopped

1/25

C-1 PAD -20degC measurement

C1 / PAD / -20degC / fnal

- 20degC

- MPPC (external trigger)

- FNALamp NO.9

Set up

(sensor No, ADC ch, Amp ch)


=> (1,0,1) (2,1,2) (3,2,15) (4,3,16)

Measurement

15:49 230V, 0.030uA , Trg rate 180Hz

16:35 run stopped

16:35 220V, 0.002uA ,

17:27 run stopped

17:27 210V, 0.002uA

18:25 run stopped

1/29

B-3 PAD -20degC measurement

B-3 / PAD / -20degC / fnal

- 20degC

- MPPC (external trigger)

- FNALamp NO.9

Set up

(sensor No, ADC ch, Amp ch)


=> (1,0,3) (2,1,4) (3,2,13) (4,3,14)

Measurement

18:09 520V, 5.14uA , Trg rate 180Hz

18:54 run stopped

Comments

Edit | Attach | Watch | Print version | History: r4 < r3 < r2 < r1 | Backlinks | Raw View | Raw edit | More topic actions
Topic revision: r4 - 2021-05-14 - TatsukiUeda
 
This site is powered by the TWiki collaboration platform Powered by PerlCopyright © 2008-2024 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback