---+ Title =HYPERLINK("#gid=1615473001&range="&address(12,match("008708",'2. electric test'!A12:12,0),4),"Link")<br />%TOC% ---++ General Information Article text. ---+ 10/19 Dual Moduleはcross talk scanもすること!!! *002106 noisescan -m 0 線源あり 300s 4chip 同じnoiseの構造* 002161,62,63 digitalscan 毎回ノイズの位置が違う 002885 exttriggerscan threshold1500 synoff *Ohio card を抜き差ししたあとは2回reboot!!* 8/27 Ohio cardに載っているresisterを外した 8/28 ・ohio cardをACのものからDCのものに取り替えてTrimを調整  →digitalscan の結果はノイズが多い、noisescanのノイずの位置は毎回違う ・lakmin board(DC)(最初に使ってたAC,8/27に使ってたDCとは別のDClakmin board)のresisterを外してみた  →digitalscanの結果はノイズが多い、noisescanのノイズの位置は毎回違う ・crosstalk scan  →bumpの剥がれを見るには   ・discbumpscan   ・thresholdscan のnoisemap   ・diffLCCをdisableして実行したanalogscan ---+++++ ohio-lakminのAC DC ~002201     ohioAC-lakminAC 002202~002274 ohioDC-lakminAC 002277~002301 ohioAC lakminDC 002302~002494 ohioDC lakminDC 002504~     ohioDC lakminDCresisterなし atlaspc14 ~006045 ohioAC lakmin DCresisterあり 006046〜006061 ohioDC lakmin DCresisterあり 006062~006076 ohioDC lakmin DCresisterなし 006077~006740 ohioAC lakmin DCresisterあり 006741~ ohioAC lakmin AC ---+++++ noisescanによるsourcescan 002780 noisescan chip4 sourceなし 3600s 002781 noisescan Chip4 sourceあり 3600s 002785 noisescan Chip3 sourceなし 3600s WorkingLog202008 ---++++ thresholdは2500だと高すぎる→高くても1500 ---+++++ exttriggerの時の注意 exttriggerscanを実行するときは configs/controller/specCfg.json ではなく、 configs/controller/specCfgFnal.json Fnal を使う!!! ---++++++ B2のPC(XpressK7)atlasj@atlaspc14 port B,DはDC, まずはPCだけ変えてやる→XpressK7でやる ---++++++ 9/4 XpressK7 使ってみる ---++++++ 9/4 違うmoduleのscanを開始 ---++++++ 9/7 XpressK7 ->Trentzボードにかえる ---++++++ 9/9 rasberrypi ~/work/CYRIC/ sudo python themo_controllCYRIC.py raspi にlogin ssh kekrasp04 温度おかしかったら source i2cget.sh ---++++++ 9/11 source scinti sensorが一直線にくるようにジグを製作 スペーサーによってそれぞれの距離を変えられる。 ---++++++ 9/29 module5 chip4 config 通らない →wireが外れていたが、visual inspectionの時点で外れていた。 ---++++++ 9/30 module6 HVのcurrentが低い BM25直後のレジスターが焼き切れていた 本来は510Ωのレジスターだが、KEKにないので50Ωの抵抗を取り付けた。 ---++++++ 9/30 moduleの温度がLVを入れるだけで50℃ モジュールとフレームのそこが接地していないので冷却がきちんとできていない →真空吸着で冷却できるようにした。 →空冷ペルチェを使用  →25℃ ---+++++ 10/2 FWを160->640に 1.FWを640Mbpsのものにする 2.controller configは specCfg-rd53a.json を使う<br />3.chip config のCdrSelSerClk を3->1 SWをコンパイル YARR内で source /opt/rh/devtoolset-7/enable mkdir builds cd builds/ cmake3 .. make -j4 make install 160のフォルダはYARR_20200903 640のフォルダはYARR_20201002になってる hirose FW を焼く FWを160 640に変えるとtrimを変えないとdata not valid cdr clk 160 3, 640 1 ---++++++ cmltapbias1->400が良い ---+++++ 10/5 大阪からpower pigtailが到着 Voltage limit 2V,4..4Aをかけて→1.992V 4.4Aで動作(module5) Lakmin 行きと帰りで1.771 V (PCB BM25)- 1.51 V(fpc vin) 落ちていますので、0.261/4.4 = 59.3 mΩ ですね。しかし、今のSetup(power board system)だと行きと帰りで59.3 mΩ + 上の写真の抵抗(power board + power pig tail +etc) = 103.1 mΩ ありますので、4.4 Aで 0.454 V落ちるはずで、1.51 V + 0.454 V = 1.963 V ぐらいがPowerSupplyで見えるはずです。 ---+++++ 10/6 scanconfigでchipconfigの値を変えられる。 prescan内 ---++++ *9/23 module2 chip1 diff lin syn* digitalscan 008123 analogscan 008133 thresholdscan 008121 totscan 008119 discbumpscan 008149 analogscan(LccDis) 008157 ---+++++ IVカーブはすぐにとること! ---++++ module4 008973 008934 008786 008849 digitalscan 008756 008779 008789 008860 analogscan lcc dis 008977 008946 008795 008863 analogscan lcc en 008986 008950 008802 008871 diff thresholdscan 008991 008954 008824 008886 lin thresholdscan 008993 008959 008828 008894 syn thresholdscan 008994 008961 008832 008896 std thresholdscan 008995 008962 008835 008897 totscan 008997 008963 008846 008899 discbumpscan ---++++ module5 chip1~3 009016 009150 009089 digitalscan 009024 009151 009090 analogscan lcc dis 009027 009152 009094 analogscan lcc en 009045 009160 009107 diff thresholdscan 009055 009169 009115 lin thresholdscan 009063 009171 009118 syn thresholdscan 009064 009172 009119 std thresholdscan 009174 009173 009175 totscan 009188 009191 009196 discbumpscan ---++++ module6 009248 009278 009324 009354 digitalscan 009250 009279 009326 009355 analogscan lcc dis 009259 009287 009332 009363 analogscan lcc en 009264 009298 009339 009371 diff thresholdscan 009269 009304 009346 009380 lin thresholdscan 009272 009305 009347 009381 syn thresholdscan 009273 009307 009348 009382 std thresholdscan 009274 009308 009349 009383 totscan 009277 009313 009351 009388 discbumpscan ---++++ scanでやること(tot tuning を行わない、linのretuneを行わない) digitalscan analogscan lcc off analogscan lcc on diff tune global threshold -t 2500 diff tune pixel threshold -t 2500 diff thresholdscan lin tune global threshold -t 2500 lin tune pixel threshold -t 2500 lin thresholdscan syn thresholdscan(config syncVth ~120) std thresholdscan std totscan std discbumpscan std exttigger ---++ Setup -- %USERSIG{KojiNakamura - 2020-08-25}% ---++ Comments
Attachments
Attachments
Topic attachments
I
Attachment
History
Action
Size
Date
Who
Comment
png
124731246312522125401253112471125191248312488_2020-09-07_23.16.31.png
r1
manage
75.0 K
2020-09-07 - 14:16
ShimpeiMidorikawa
This topic: Main
>
WebHome
>
RD53ADAQtop
>
RD53ARealQuadDAQ
Topic revision: r39 - 2020-10-19 - ShimpeiMidorikawa
Copyright © 2008-2025 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki?
Send feedback