Jun2016CERNTBLog < Main

back to [[June2016CERN][June Testbeam page]]
---+ June 2016 CERN Testbeam Logbook

%TOC%
---++ Add Log

May 25 9:00    Starting Testbeam preparation at H6A beam area. Setup HSIO2 and updated Firmare.

-- %BUBBLESIG{KojiNakamura - 2016-05-25}%

June 6 non-irrad sensor tuning start & done, Auto trigger data taking (3dut & 5tel) in beam line -&gt; OK

-- %BUBBLESIG{AtlasjSilicon - 2016-06-06}%

June 6 22:47 check long auto trigger run (about 3h, 3dut & 5tel) -&gt; telescopes & DUT are stable (don't stop run) by K.Sato

-- %BUBBLESIG{AtlasjSilicon - 2016-06-06}%

June 7 10:30 Updated firmware on Artex-7 of IFAE(AFP)'s HSIO2 (HsioCosmic _V11N_CosmicNew.bit) by H. Sawai

-- %BUBBLESIG{AtlasjSilicon - 2016-06-07}%

June 7 11:00 Started tuning for irrad-module by H. Sawai

-- %BUBBLESIG{AtlasjSilicon - 2016-06-07}%

June 7 19:36 Succeeded in remote controlling from the hut. Started 3SCC auto-trigger run with GeoID:31. by H. Sawai

-- %BUBBLESIG{AtlasjSilicon - 2016-06-07}%

June 7 23:47 Started run for 3SCC (no beam yet). GeoID:31, Run Number:1930~ by H. Sawai

-- %BUBBLESIG{AtlasjSilicon - 2016-06-07}%

June 7 23:52 All sensor tuning done by K.Sato

-- %BUBBLESIG{AtlasjSilicon - 2016-06-07}%

June 8 23:34 Adjusted position of 3 SCCs, and started run (Run Number:1950~) by H. Sawai

-- %BUBBLESIG{AtlasjSilicon - 2016-06-08}%

June 9 10:04 KEK105,106,108 connectivity check at control room, but tuning is not good...(connecivity is OK) so need to tune in beam line before test by K.Sato

-- %BUBBLESIG{AtlasjSilicon - 2016-06-09}%

June 10 4:00 check sensor condition, KEK105RJ3 is out, other sensor install run control. but beam is stopping now...

-- %BUBBLESIG{AtlasjSilicon - 2016-06-10}%

June 10 6:00 beam on & start alignment

-- %BUBBLESIG{AtlasjSilicon - 2016-06-10}%

June 11 8:30 5telescope run start (runnumber=2118). Please check run spreadsheet

-- %BUBBLESIG{AtlasjSilicon - 2016-06-11}%

June 10 morning~June 11 night summary

- 4chip run(KEK105,106,108) alignment OK & start

- HSIO2 inlink, outlink config file is incorrect -&gt; change correct config file -&gt; can take beam data

- include noise scan mask
- make 4chip run reconstruction program, so please check&#x3000;run quality sometimes

- telescope4 remove June 11 night, because of non event build. -&gt; change 5telescope June 11 8:30

-- %BUBBLESIG{AtlasjSilicon - 2016-06-11}%
%COMMENT%
---++ More Information

-- %USERSIG{KojiNakamura - 2016-06-05}%
This topic: Main > PlanerPixelTestBeam > June2016CERN > Jun2016CERNTBLog
Topic revision: r11 - 2016-06-11 - AtlasjSilicon