July 2018 CERN TB log

>>>>> RD53A testing at kek log<<<<<

>>>>> RD53A testing at cern<<<<<

Gateway 192.168.5.251
YARR 192.168.5.25
HSIO2 192.168.5.26

03 July 2018

[午前中]

原田→CERN ID及びPersonal Dosimeterの入手

中村さん、内山、Jhon→Personal Dosimeterの入手及びH6B control roomに荷物の運び入れ

2枚目のXpressk7を借りる

[午後]

ohio cardでmodule testing

TEXIO power supplyだとdigital currentが0.05Aぐらいしか流れない→ohioのせい?

USBpixのregulatorを使ってみる

digital currentが低い理由は、ohio cardのmini DPに挿す場所が違ったのが原因(Port D(写真右端のport)に挿していた) 正しい場所はPort A(黄丸)

ohio_connection.png

04 July 2018

[12:30]

KEK53-7

global-local tune target 4000

002291_thresholdscan

lin/diffともにtuneができた。

configの変更点

diffLccEn 0->1

diffVff 50->150

diffPrmp 500

diffPrecomp 100->150

LinKrumCurr 50->80

[16:00]

YARR+HSIO2用のPC(zenpc)をビームラインに移動→IP : 192.168.5.25

FEI4のLV電源はTEXIOではなく、ビームラインに置かれていたもの( Fernell element14社製 R&S HMP4040)を使用

LV ch. assign

ch. for... Voltage
1 FEI4 VDDD 1.2V
2 FEI4 VDDA 1.4V
3 USBpix power 2.0V
4 not connected -

TLU assign

ch. for...
2 HSIO2
3 YARR
[16:00]

tunnig組。

diffのみ target 3000e
3000eよりも前でピーク。低いスレッショルドでなだらかになり、3000eあたりで急に切れる。
->thresholdscanの取り方の問題。解決。
data : 002329


KEK53-7のtunnig
diffのみ target 1500e(localまで)
data : 002367

diffのみ target 1000e(globalのみ)
data : 002369

lin
target 3000e(global)
Vth400->350
data : 002427

3000e以下にしようとするとうまくいかず。

夕食前後~

linについて。
EnCoreColLin
65535->61140
に変更し、領域を狭くした。
2500eにまでtuneできた。
Vth 400->350

data : 002427

Vth 400->300
うまくtunningできず。

現在2500e以下には合わせられていない。

05 July 2018

[0:00]

ohioカードXpressK7を焼くためにatlaspc9のXilinxsを2016.2に.

zenpcにHSIO2primlistを入れる.

FE-I4のThreshold2400eにチューニング

[2:00]

zenpcでRD53A作動

[9:30]

KEK53-4のtuningから再開

スプレッドシートにRD53Atunningの項目を追加。moduleとscan結果の対応表。

dataの場所は/work/XpressK7_RD53A/YARR-20180703devel/src/dataの中

Logにも詳細は並行して書いていく。

KEK53-4

digitalscan

data : 002466

analogscan

data : 002483

この時のconfigの変更点

diffLccEn 0->1
linkrumCurr 50->120

diff_threshold

target 1000e

変更点
DiffVth1 250->100
DiffVth2 50->20
2000eぐらいのところで二つ目の山。
data : 002507

lin_threshold

target 2000e
領域を狭くしてのtune.
data : 002519

std_thresholdscan

target 3000e
領域狭くせず
変更点
DiffVth1 250->100
diffLccEn 0->1
linkrumCurr 50->120

data : 002563

std_thresholedの場合2000e/4000eでピーク。
lin_threshold 3000e/diff_threshold 3000eでピークを確認
data : 002564,002565

analog scanを回すとdiff FEのバイアス構造がない部分で応答が悪くなる→LccEn=0にするとちゃんと返ってくる

diff_analogscanを回すと起こる現象だった(std_analogscanだと発生しない)→Trigger Loopのfrequencyが影響していそう(diff_analogscanでfrequency 10000→5000にするとちゃんと返ってきた)

KEK53-11

digitalscan

data:002641

analogscan

data:002649

configの変更点

diffLccEn 0->1
linkrumCurr 50->120

diff_thresholdscan

target 1200e

data:002655(but)

data:002729(good)→002869

line _thresholdscan

target 2000e(狭)

data:002674

std_thresholdscan

3000e

std_thresholedの場合2000e/4000eでピークになっていたが、

lin_threshold 3000e/diff_threshold 3000eでピークを確認。

data:002684

std_thresholdscan(but?)

target 2000e

領域を区切らずに。

data:002723

line/digital

data:2720/2721

KEK53-12

digitalscan

data:002905

analogscan

data:002906
変更点
DiffLcc
DiffPrep 650
Vth1 100
Vth2 20
LinkKrumCurr 50->100

diff_thresholdscan
target 1200e
data:002931

KEK53-13

digitalscan

data:002935

analogscan

data:002938

diff_thresholdscan

target 1200e

data:002941

06 July 2018

[1:00]

micro usb -ethernetのトリガーやビジーが反転問題を修正したFWを焼くがスキャンを行うとデータが返ってこない。

HSIO2のデバック終了。クロックトリガーで問題なく動作。

[3:00]

yarrもFWを焼き直して修正。

[4:00]

HSIO2,YARRの両方を入れたクロックトリガーが正常に動作。

YARRの処理が遅い?500Hzでは追いつけない,300Hzは追いつける

HSIO2(rce offline producer)->YARR(YARR producer)の順に立ち上げること

[9:20]

ohio card+Xpressk7をビームラインから回収、control roomでtuning再開

kekatlaspc9に最新のYARR(FEごとに異なるthresholdでtuningできるようになった)のgit cloneを行った

>>>>>No beam for NA before early afternoon.<<<<<

KEK53-6

digitalscan

data:003315

analogscan

data:003320
はじめそのままconfigが汚かったり、返ってこなかったりした。
返ってきたら汚くともconfigを変えるときれいに返ってきた。
configの変更点
SldoAnalogTrim26->20

diff_thresholdscan

target 1200e
data:003327

KEK53-9

digitalscan

data:003373

analogscan

data:003375

KEK53-6と同じ現象。

configの変更点

SldoAnalogTrim26 ->22

linerのポリシリのない領域(中央下)のanalogscanが返ってこない。diffのみのtuneのためこのままtunning

->調査中。

diff_thresholdscan

target 1200e

data:003382

target 1000e

data:003460

KEK53-7

digitalscan

data:003394

analogscan

data:003395

KEK53-6と同じ現象。
configの変更点
SldoAnalogTrim26->16

diff_thresholdscan

target 1200e
data:003399

target 1000e
data:3411

[14:00]

>>>>>>No beam for NA before late afternoon .<<<<<<

[19:30]

beam復活、YARRとHSIO2をintegrationして動かしてみる

07 July 2018

[9:00]

6:40頃からbeam無い状態

tuningを進める

[11:00]

ビーム復活

scanするとマスクされる問題


RD53A tunningではそれぞれのscanをすると勝手にmaskされてしまうという問題がある。
./primlist/scan53.sh digitalscan KEK53-**
とすると、maskされてしまう。
./primlist/scan53.sh digitalscan KEK53-** -m 0
とすると、maskはされず、そのままを維持。
-m 1に変えると今までのmaskはリセットされる。
よって、tunningが終わったら、リセットしてからmaskすることが必要。

tunningの後、

./primlist/scan53.sh digitalscan KEK53-** -m 1

とすること。

[17:00]

latency scan開始 latency : 253から

ビームトリガーだとlin FEとdiff FE部分にノイズがのる→DP to Ethernet boardのGNDとTLUのGNDが浮いているせい?

noise scanでビームを見てもこのノイズは発生しない←見えてるのは本当にビーム???

[21:00]

No beam due to septa problem.

beam offでauto trigger modeで走らせると、noise scanに似た結果が得られた→trigger由来のノイズ?

DP to Ethernet boardのコネクタ同士のGNDをソルダージャンパーで共通にした→後ほどビームラインに

[22:56]

ビーム復活

lin FEのノイズはTLU GND由来ではないかもしれない←GND共通にしてもノイズ発生した

08 July 2018

[10:00]

ToT Scanは-t optionでinjectionを指定できる

10000injection設定、現行configでtot scanをすると、lin FEが大体4、diff FEが大体15あたり

LinKrumCurr : 30,DiffVff : 80に変更、totを7に設定

[11:30]

ビーム止まる

[12:00]

linをマスク(syn off)したconfigでdigitalscan/analogscan/noisescanによるマスクをかぶせたconfigを生成。

data:00657->000694(threshold tuneし直し)

stage位置合わせ

x=36,y=33 中心付近にビームらしきもの run 611

x=36,y=28 ノイズしか見えない run 612

x=30,y=33 ノイズしか見えない run 664

x=42,y=33 ノイズしか見えない run 665

x=30,y=33 Syn,Linをマスクしても見えない.マスクしてるはずなのに全体にノイズ run 670

[14:00]

Diff FEのビーム測定時のThreshold.

bias rail構造有りでは1500eではとてもノイジー.

1800でも少しうるさく2000eではほぼない.

bias rail構造なしでは1000eでは数ピクセルノイジーな程度.

1000e以下ではthreshold チューニングができない.

[15:30]

ビームラインにgame PCを設置→IP : 192.168.5.26

[17:00]

ビームでる

[17:20]

ビーム止まる

[17:25]

ビームでる

latency 420BC+/-50くらいにあるはず.

[2:13]

latency 347!

位置は(36,31)

diff threshold 1200e

lin threshold 3000eに変更。

KEK53-7 config

LinVth : 400 -> 360

DiffVth1 : 250->100

DiffVth2 : 50->20

LinKrumCurr : 50 ->30

DiffVff : 50 ->80

syn/linはoff

場所は

~/work/yarr_rd53a/Yarr/src/data 

の中の

data : 000966(lin_threshold)

09 July 2018

[17:30]

beamが戻ったがrunを走らせると、calibserverがコアダンプする現象が起こった。

→HSIO2及びPCの再起動を行ったが解決せず

->RceOfflineProducerの引数の1つのserver IPが192.168.1.77のところ192.168.1.177にしてしまっていたため

上記PC再起動の際に間違って(?)local networkがささっているportをoffにしてしまったらしく、localがしばらく繋がらなくなった→アクセスしてonにしてきた

[18:30]

上記問題修正。

10 July 2018

[12:00]

bias structure部分をmaskする(かなりひどい)codeをpcx17261に移植し、上半分のmaskが出来るようになった

ついでにmapやdistを作るものも移植した(こっちは後で消すかも)

11 July 2018

[2:00]

Yarr version 20180710v.2に戻してlong run

[3:00]

Yarr version 20180710v.10

correlation消えない!

yarrった!

[5:00]

run plan (仮)決定。

[5:40]

beam stop

-- Atlasj Silicon - 2018-07-03

Comments


Topic attachments
I Attachment History Action Size Date Who Comment
PNGpng ohio_connection.png r1 manage 134.6 K 2018-07-04 - 12:34 AtlasjSilicon  
Edit | Attach | Watch | Print version | History: r56 | r35 < r34 < r33 < r32 | Backlinks | Raw View | Raw edit | More topic actions...
Topic revision: r33 - 2018-07-11 - AtlasjSilicon
 
  • Edit
  • Attach
This site is powered by the TWiki collaboration platform Powered by PerlCopyright © 2008-2024 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback